How To Get The Spare Tire Off A Chevy Colorado

If your own a Chevy Colorado and want to remove its spare tire, you may be wondering how to go about it. Fortunately, we have done the legwork for you, and here is what we found.

The following are step by step procedures for removing a spare tire from Chevy Colorado:

  • Locate the spare tire access hole
  • Make an extension rod 
  • Insert the rod into the access hole
  • Turn the rod anticlockwise

This is an easy task, all you need to do is follow the steps carefully. Sit tight and keep reading to get detailed information on how to remove a spare tire from Chevy Colorado.

The Chevrolet Colorado Xtreme Concept is on display during The 37th International Motor Show , How To Get The Spare Tire Off A Chevy Colorado

How To Get The Spare Tire Off A Chevy Colorado

Tool kit for changing car tires. Jack lifts important for change spare tire.

Before starting the task, you need to get a jack kit, female rod, and crowbar ready.

Click here to see this jack kit on Amazon.

After that you can then proceed with the following:

Step 1: Locate The Spare Tire Access Hole

The first step is to find and locate the access hole on the spare tire. The access hole, which is covered with plastic in the shape of a rectangle, is located on the right side of the rear license plate, just like it is on other trucks.

Recent models of Chevy Colorado feature a lock that covers the hole for more protection. In such cases, the lock assembly that covers the hole can be removed by using the ignition key.

Step 2: Make An Extension Rod

After locating the access hole, you have to make an extension rod that is long enough to insert into the access hole.

Open up your jack kit, and find the rod that has a wider end with flanges on all sides. This rod, known as the "female" rod, will be inserted into the access or keyhole, which you have already opened.

Click here to see this female rod on Amazon.

To make the female rod long enough to reach the spare tire from the bumper, obtain another rod from the tool kit and attach it to the end of the female rod. This will make the female rod longer. Make sure that the press locks are properly engaged in order to prevent the rods from disconnecting while turning it.

Step 3: Insert The Rod Into The Hole

Insert the composite rod into the access hole in the spare tire. At this point, you have successfully inserted one end of the rod into the hole. The other end of the rod, the one that is not going into the bumper, should be attached to the crowbar.

Maintaining simultaneous pressure and rotation on the rod will allow the end to be locked into the cable crank. After that, move on to the next step where you will give the crowbar a turn in a clockwise rotation and lower the spare tire to the ground. 

Step 4: Turn The Rod Anticlockwise

After putting a wrench or crowbar on the opposite end of the extension rod, then turn it in the opposite direction that is anticlockwise.

As you turn the crowbar, the tire will start to drop down. Keep turning the crowbar until the tire reaches the ground, at which point you will be able to remove the cable flange from the rim.

In addition, the approach described above is not limited to only Chevy Colorado. It can be used for a variety of different Chevy truck models. 

Click here to view this crowbar on Amazon.

How Long Can You Drive On A Spare Tire?

The maximum distance that spare tires can be used safely is approximately 50 miles before they need to be replaced. After that point, they pose a risk to both you and the other drivers on the road.

Even if you have no choice but to travel farther than 50 miles, you should try to avoid driving on your spare for more than 70 miles. It is not the work of a spare tire to entirely replace a worn-out tire; rather, its function is to hold you over until you can replace the worn-out tire in the appropriate manner. 

Can You Reuse A Chevy Colorado Spare Tire?

Yes, you can reuse your Chevy Colorado spare tire. However, the majority of manufacturers of motor vehicles agree that a temporary spare tire should only be used for a short period of time.

As a result, it is suggested to limit your speeds to or below 50 miles per hour on a spare tire before getting your flat tire fixed. But this is only applicable to small-sized spares. 

It is possible to install and reuse certain full-size spare tires that are designed to match the size of the other four tires on the vehicle for longer distances while traveling at regular speeds.

But since these spares are not used very frequently, before reusing them, make sure that the air pressure is set to the specifications provided by the manufacturer and that the tire does not have any obvious problems or excessive wear. 

In the event that there are any problems, it is best to continue with extreme caution and seek the guidance of a professional.

Can You Use A Spare Tire From Another Car?

spare tire under of the car

No, spare tires and wheels that are included with a car are custom-made to work exclusively with that automobile. As a result, never make the mistake of using your spare tire and wheel on another vehicle unless it is the exact same make and model as your vehicle.

How Do You Change A Chevy Colorado Tire?

To change your Chevy Colorado tire, follow the step-by-step guide below:

Step 1: Find A Safe Location

Handsome young man lifting the car on the jack for changing flat tire on the road

Avoid unnecessary stops or turns after discovering that your tire is flat. Calm down and look for a straight, flat section of road with a big shoulder.

It would be perfect if it were in a deserted parking lot. Your vehicle will be less likely to roll if the ground is flat. Never change a tire when surrounded by incoming traffic on a narrow shoulder.

Step 2: Turn On Your Emergency Flashers

Emergency button in the car.

Flashers, often known as hazard lights, will alert oncoming traffic that you are stopped on the roadside. As soon as you notice you need to stop, turn them on.

Step 3: Position The Wheel Wedges

To prevent the car from moving while you change the tire, place wheel wedges in front or behind the wheels. Keep these in front of the front tires while you work on the back ones. Wheel wedges should be placed behind the back wheels if the flat one is in front.

Click here to see this wheel wedge on Amazon. 

In place of actual wheel wedges, bricks or huge stones will work just well. Ensure that they are sufficiently sized to prevent the vehicle from rolling away.

Step 4: Unscrew The Lug Nuts

The lug nuts need to be turned counterclockwise with the lug wrench until the resistance is broken. Use whatever force is necessary; that's fine. If you need to, you can use your whole body weight or only your foot. The lug nuts should be loosened by a quarter to half a turn, but not totally removed just yet.

Step 5: Jack Up Your Car

Before attempting to raise your vehicle, you need to position it well. Place a short piece of two by six inches block wood beneath the jack to keep it from sinking under the weight of your vehicle and tipping over.

After positioning the jack, lift your vehicle until the flat tire is roughly six inches off the ground. Under no circumstances should any portion of your body be placed under a car while using a jack to raise it!

You need to take the lug nuts off completely now. Since you have initially loosened them up, you should be able to remove them by hand. After the nuts have been removed, grab the tire by the treads and pull slowly toward you until the tire is free from the hub in the back. 

Step 6: Fix The Spare Tire

Align the rim with the lug bolts and mount the spare tire to the hub. Gently push until the lug nuts are visible through the wheel. Reattach the lug nuts to the lug bolts and hand-tighten them to the maximum. When you have them all on, double-check their tightness and then tighten them even more.

When the car is at ground level, tighten them again using the wrench. With the help of the jack, lower the car to the ground until the spare tire touches the ground, but not completely.

Tighten the lug nuts at this point as much as possible, by twisting the wrench clockwise. Use all of your weight to push down on the lug wrench. Then, lower the car completely to the ground and take out the jack. Again, use the wrench to ensure the lug nuts are as tight as they can be.

To Wrap Up

If you want to take off the spare tire on your Chevy Colorado, all you have to do is locate the spare tire access hole, make an extension rod, insert the rod into the access hole, and turn anticlockwise.

If you enjoyed reading this post, here are similar articles you may like:

Largest Tire Size For Honda Ridgeline - Can You Go Bigger?

How To Reset Tire Pressure Sensor GMC Sierra [With And Without A Tool]?