If you own a Chevy Colorado, you may be wondering how to jack it up when the need arises and where the jacking points are located. Luckily, we have done the research for you, and here is what we found.
The jack positions in Chevy Colorado are directly behind the front wheels and just in front of the back wheels, underneath the rocker panels. Follow this step-by-step guide to jack up a Chevy Colorado:
- Move the truck to a flat surface
- Put the truck in park, turn off the engine, and chock the wheels
- Locate the jacking point behind the wheels
- Fit the Jack
- Lift the car
- Bring down the car when finished
Jacking up a Chevy Colorado is an easy-to-do task, all you have to do is follow the steps carefully. Keep reading to get detailed information on how to jack up a Chevy Colorado
![plainfield-circa-july-2022-chevrolet-colorado-sunny hot day, How To Jack Up A Chevy Colorado [And Where Are The Jack Positions?]](https://veasks.com/wp-content/uploads/2022/10/How-To-Jack-Up-A-Chevy-Colorado-And-Where-Are-The-Jack-Positions-1200x800.jpg)
Where Are The Jack Positions In Chevy Colorado?
The jacking points in Chevy Colorado are just behind the front and back wheels. The car jack is required whenever you need to raise your car to perform an emergency repair, like changing a flat tire, or if you need to spend longer time under the vehicle to change the engine oil or the exhaust system.
They are also used in garages to make it easier to raise the vehicle's level so that the mechanic can access its undercarriage and make repairs.
Depending on the device's size, jacks are available in a variety of sizes and can lift a range of weights. Jacks are very dependable when used correctly and are capable of lifting small cars and large trucks.
Click here to see this car jack on Amazon
How To Jack Up A Chevy Colorado
To jack up your Chevy Colorado safely, here are easy steps to follow:
Step 1: Move The Car To A Flat Surface
If you get a flat tire unexpectedly in the middle of the road, pull off the road and away from the flow of traffic. The aim is to completely exit the road and move to a flat, stable area, such as a parking lot, where you can safely use a car jack.
If that doesn't work, try to find a road or street with little to no traffic so you can drive off to the side, away from the traffic, and find a strong enough area to support a jack. If the surface is soft, the jack may lean to one side while lifting the automobile, which could result in the vehicle dropping.
Step 2: Prep The Car
After finding a good location that will support the jack, the next thing to do is to secure your car. Make sure it is in park, the engine is off, and the parking brake is applied.
After that, place a block or stone under each tire in such a way that it is opposite the way you are going to jack up. Securing provides additional protection and prevents the car from rolling off the jack. It's a recommended to let passengers out of the car if you have any.
Step 3: Check For The Jacking Points
After you have stabilized your Chevy Colorado, get out your jack and find the jacking points - the spots on the body of the vehicle with extra strength. In order to safely lift the car, most automobiles have strengthened metal ribs that serve as the jacking points.
Four jacking points are included on the Chevy Colorado. They are situated beneath the car's rocker panels, immediately behind the front and back wheels. However, you can check your owner's manual to be certain of where your vehicle's jacking points are located.
Step 4: Fit The Jack
After locating the jack points, you need to position you jack correctly to the jacking points. Although your Chevy Colorado model may have a different setup, check your owner's manual to make sure you know exactly how your jack interacts with the jacking point.
However, most Chevy Colorado model jacks have a slot at the top of their engagement flange that slips onto the reinforced rib of the jack point.
Step 5: Lift The Car
When you have successfully position the jack correctly on the jack point, it is now time to jack the car. Slowly turn the jack handle in a clockwise manner till the flat tire is raised off the ground.
Take your time, and make sure the jack is held straight up and down so that the can may be raised. The jack shouldn't lean to one side because it won't hold the car firmly in that position.
You should set a jack stand under the rocker panel close to the jack and secure it to the car's body. This will guarantee that the car won't fall on you if things should go wrong.
Step 6: Bring Down The Car
When you are done, lower the vehicle. Carefully unwind the jack handle in the opposite direction (counterclockwise) until the tires touch the ground and then, you can remove the jack.
How Many Jacks Do You Need?
The number of jacks needed will depend on the type of work involved, as well as the size and model of your vehicle. You might need to lift the entire automobile, the front end, the rear end, or just one wheel.
In general, most drivers only need one jack. This is because you'll only need to lift one wheel to change a flat tire. If you want to elevate one end of your vehicle, ou will need two jack stands. However, you will need four if you are lifting the entire vehicle.
Knowledge is very important in jacking a car. Knowing what to do at the right time can prevent different issues. Jacks can stay upright even on soft ground like grass if a thick plywood is used to support the jacks.
Make sure you are familiar with the best safety procedures and the location of the jack points for your specific vehicle model before attempting to jack a car.
Your car's owner's manual will certainly contain several pieces of information you need to know to jack your vehicle safely as well as the number of jacks that are needed for a specific task.
Can You Jack Up Chevy Colorado By The Differential?
Yes, it is possible to jack up your Chevy Colorado using the differential. However, it is not advisable to do so. Unless the manufacturer specifically advises so, you shouldn't jack up your car using the differential.
How High Can You Jack Up Chevy Colorado?
No particular height is required to jack up Chevy Colorado. However, most cars can be jacked to a maximum height of 20 inches. If you are lifting very large custom tires tires, in this case, you may need more clearance.
You can find instructions on how high to jack your car in the owner's manual and owner's handbook for your specific model of car such as the Chevy Colorado. Always refer to your owner's manual before attempting to jack; failing to do so could endanger your safety and even harm your car.
However, you can be able to jack a Chevy Colorado as high as your jack will allow. You can even put a wood block on your jack to give it a little bit more lift if it won't go high enough.
As a safety precaution, never attempt to enter under the vehicle while it is being supported by any kind of jack; instead, once the car has been raised to the required height, support it using jack stands.
Can You Jack Up Chevy Colorado On The Frame?
Yes, anywhere on the Chevy Colorado frame can be jacked. All potential locations inside your Chevy Colorado that can support and accommodate the jack is usually listed in the owner's manual.
How Long Can Chevy Colorado Sit On Jack Stands?
There is no particular or limited period of time Chevy Colorado can sit on jack. Your car can sit on jack stands for long. You can leave your car for days, weeks, months, or even years on jack stands as long as it is jacked on a flat surface.
Final Takeaways
In Chevy Colorado, the jack positions are at the back of the front wheels and just in front of the back wheels. To jack up your Chevy Colorado, all you have to do is move the car to a flat surface, prep it,
check for the jacking points, fit the Jack, lift the car, and then bring it back down.
If you enjoyed reading this post, here are similar articles you may like:
How To Put The Jack Back In A GMC Sierra?
